The Dynamic Indoor Rower offers the closest simulation to rowing on the water and was developed to meet the specific training needs of the competitive rowing athlete. Comes equipped with a PM5. Not available to order online. Please contact Concept2 Benelux for more information
The Model E offers presence and durability with its 20 inch frame height, nickel-plated chain, and glossy clear coat finish. Comes in gray or black and is equipped with a PM5.
Add an on water feel to your Model A, B, C, D or E Indoor Rower with the Concept2 Slide!
If you already have a pair of Concept2 Slides and want to be able to link two or more indoor rowers together to simulate a "double" for great team training, you can purchase a spare slide (one slide, as pictured).
Our most advanced Performance Monitor. Features wireless heart rate monitoring, the ability to store workouts to a USB flash drive (sold separately), and is backlit for improved visibility in low light environments. See more info.
Intended for use with our Dynamic Indoor Rower, the Dynamic Link allows you to connect two or more Dynamic Indoor Rowers so you can train as a crew. if you buy two Dynamic Indoor Rowers, we’ll include a Dynamic Link for free!
Water-resistant cover for Models A, B, C or D Indoor Rowers.
The Indoor Rower Floor Mat is made out of 4 mm thick black rubber and measures 250 cm by 80 cm. The mat can be used on any surface and helps protect the floor as well as eliminate slippage.
The iPhone Connection Kit is used to connect a PM3, PM4 or PM5 to an iOS device for using software such as ErgData. Important: See more info for System Requirements prior to purchase.
For use with Model D and E Indoor Rowers. This is the generator base and coil that transmit flywheel motion to and generates power for the Performance Monitor on your indoor rower. See more info.
For use with Model B Indoor Rowers only. 20" long pickup (sensor) and cable (wire) that transmit flywheel motion to the Performance Monitor on your indoor rower. If your monitor lights up with zeros but the display does not change when you begin rowing, you may need to replace this part. If the cable or cable housing is cut or broken you will definitely...
This is the damper-side cover for the gray Model D and Model E Indoor Rower. Does not include the four damper fan cover screws (order separately, part number 1276). See more info.
For use on the Model D and E Indoor Rower.
If you already own a Polar™ or Polar compatible heart rate chest belt transmitter and would like to enable the PM2/PM2+/PM3/PM4 heart rate monitoring function on your Concept2 Model A, B, C, D, or E Indoor Rower, this Concept2 Heart Rate Receiver is what you need.
For use on the Model D and E Indoor Rower. This is the 14 tooth sprocket for the flywheel axle. If you need to replace the sprocket, you should replace the chain at the same time (see part number 1916). See more info.
For use with Model A and C Indoor Rowers. This is the pickup (sensor) and cable (wire) that transmit flywheel to the Performance Monitor on your indoor rower. If your monitor lights up with zeros but the display does not change when you begin rowing, you may need to replace this part. If the cable or cable housing is cut or broken you will definitely need...
Replacement handle for the Model D, E and Dynamic Indoor Rowers. Overmolded grips made of soft rubber won´t absorb sweat, grease or dirt. Does not include U-bolt nuts. See more info.
This is the handle drive cord for a Dynamic Indoor Rower. The handle drive cord is a single cord that is connected to the handle on one end and the foot carriage on the other end. Not for use on Model A, B, C, D, or E. See more info.
For use on all Concept2 Indoor Rowers. Replacement seat top. 12" wide, 10" deep, 1½" thick, with contours for pelvic bones and tailbone. Mounting screws and lock washers (four each) included. Original equipment on Model C, D, E and Dynamic Indoor Rowers. Can be retrofitted on all Model B and most Model A Indoor Rowers, replacing the original "kidney"...
For use with Model C, D, E and Dynamic Indoor Rowers. One of the 3-1/4 inch wide top seat rollers (two per machine; sold individually) that runs on the stainless steel track on the monorail. Mounting hardware that holds the roller on the seat frame is not included, because it can usually be re-used. If you need the hardware, order part number 1728...
Let’s face it: the backside works hard during rowing. If you prefer a bit more padding, try our seat pad. Made from 12mm textured rubber, this provides the comfiest row around with cut out sections in the middle for the pelvis and at the rear to accommodate the coccyx. The seat pad can be easily transferred between machines.
This special nut tool is required to replace the flywheel axle sprockets on Model C, D or E Indoor Rowers. Model D and E Axle and Sprocket Replacement
For use with Model A and B Indoor Rowers. This is one of the 2¼" wide seat rollers that run on the top and bottom of the stainless steel tube monorail. Includes the seat roller bearings (sealed inside). Does not include mounting hardware. If you also need mounting hardware, order part number 378 instead. See more info.