skip to main content
Model E
Parts listed here are compatible with Model E Indoor Rowers (manufactured from August 2006–present).

Model E There are 34 products.

per page
Showing 1 - 25 of 34 items
  • 200,00 €
  • 36,51 €

    For use with Model C, D and E Indoor Rowers. Includes on 8' 4" long chain with a brass swivel at the handle end and chain connector for the inside end. If your chain is badly rusted, has seized links or is broken, you will need to replace it with this part. See more info.

    36,51 €
  • 26,20 €

    For use with Model D and E Indoor Rowers. This is the generator base and coil that transmit flywheel motion to and generates power for the Performance Monitor on your indoor rower. See more info. 

    26,20 €
  • 20,00 €

    Replacement handle for the Model D, E and Dynamic Indoor Rowers. Overmolded grips made of soft rubber won´t absorb sweat, grease or dirt. Does not include U-bolt nuts. See more info.

    20,00 €
  • 15,00 €

    For use on the Model D and E Indoor Rower.

    15,00 €
  • 15,00 €

    For use on all Concept2 Indoor Rowers. Replacement seat top. 12" wide, 10" deep, 1½" thick, with contours for pelvic bones and tailbone. Mounting screws and lock washers (four each) included. Original equipment on Model C, D, E and Dynamic Indoor Rowers. Can be retrofitted on all Model B and most Model A Indoor Rowers, replacing the original "kidney"...

    15,00 €
  • 13,50 €

    For use with Model C, D, E and Dynamic Indoor Rowers. One of the 3-1/4 inch wide top seat rollers (two per machine; sold individually) that runs on the stainless steel track on the monorail. Mounting hardware that holds the roller on the seat frame is not included, because it can usually be re-used. If you need the hardware, order part number 1728...

    13,50 €
  • This special nut tool is required to replace the flywheel axle sprockets on Model C, D or E Indoor Rowers. Model D and E Axle and Sprocket Replacement

  • 7,50 €

    For use on the Model D and E Indoor Rower. This is the 14 tooth sprocket for the flywheel axle. If you need to replace the sprocket, you should replace the chain at the same time (see part number 1916). See more info.

    7,50 €
  • 7,50 €

    For use with Model C, D and E Indoor Rowers. This is the 12´ 6" long elastic shock cord (or bungee cord) that recoils the chain on recovery. If your chain recoils slowly—or not at all—between strokes, then you should inspect your existing shock cord. See more info.

    7,50 €
  • 6,50 €

    For use with updated Model D, Model E and Dynamic Indoor Rowers. Also fits Model C and original Model D Indoor Rowers but is dark gray in color (for black, order part number 1017 instead). This flexfoot piece fits into the footstretcher covers (part numbers 1054 and 1055, sold separately) to make the complete footstretcher assembly. Footplate/Flexfoot...

    6,50 €
  • 4,76 €

    For use on the Model C, D and E Indoor Rower. This is the part that the chain passes through before entering into the flywheel assembly. See more info.

    4,76 €
  • 4,24 €

    For use with Model A, B, updated D, E, Dynamic Indoor rowers and the black SkiErgs manufactured from August 2014–present. This is the right caster wheel.

    4,24 €
  • 4,24 €

    For use with Model A, B, updated D, E, Dynamic Indoor rowers and the black SkiErgs manufactured from August 2014–present. This is the left caster wheel.

    4,24 €
  • 4,01 €

    T27 6-Lobe driver required to turn the front leg fasteners (part number 2952) on Model C, D (original and updated) and E Indoor Rowers.

    4,01 €
  • 3,60 €

    For use with the updated Model D, Model E and Dynamic Indoor Rowers. Left footstretcher cover. The flextfoot piece (part number (part number 1063, sold separately) fits into this part to make the complete footstretcher assembly. Footplate/Flexfoot Assembly Diagram

    3,60 €
  • 3,60 €

    For use with the updated Model D, Model E and Dynamic Indoor Rowers. Right footstretcher cover. The flextfoot piece (part number (part number 1063, sold separately) fits into this part to make the complete footstretcher assembly. Footplate/Flexfoot Assembly Diagram

    3,60 €
  • 3,50 €

    For use with Model C, D, E and Dynamic Indoor Rowers. This is one of the small bottom seat rollers (two per machine; sold individually) that runs under the top edge of the monorail. Does not include the mounting hardware (nut, bolt and spacers) that hold the roller on the seat frame, because it can usually be reused. If you need the hardware, order part...

    3,50 €
  • 3,00 €

    For use with updated Model D, Model E and Dynamic Indoor Rowers.  Replacement nylon footstrap with buckle, approximately 30" long by 1" wide with a screwhole drilled approximately 9" from the buckle end. Two per machine. Sold individually. Model D/E Flexfoot Assembly Diagram

    3,00 €
  • 2,90 €

    For use with Model C, D and E Indoor Rowers. This is a 3-3/8 inch diameter pulley that the shock cord (part number 1731) runs over inside the Concept2 Indoor Rower. There are four per machine. Sold individually. See more info.

    2,90 €
  • 2,50 €

    For use with Model C, D and E Indoor Rowers. These are the 1¼" diameter urethane pulleys that the chain runs over inside the indoor rower. There are two per machine: one is part of the traveling pulley (part number 1756); the other is mounted on a stationary axle and has two chain idler spacers (part number 1305) to keep it properly aligned. See more info.

    2,50 €
  • 1,82 €

    For use with Model A, B, C, D, E and Dynamic Indoor Rowers. This is the hard plastic cap that goes on the rear and/or front metal legs of the indoor rower to protect your carpet or floor and keep the machine from sliding back and forth while you row. Two to four per machine, depending on age and indoor rower model. Sold individually. See more info.

    1,82 €
  • 1,25 €

    For use on all Model C, D and E Indoor Rowers. This swivel bushing is installed at the swivel/handle end of the chain to prolong chain life and provide smoother rowing. See more info.

    1,25 €
  • 1,21 €

    For use with Model C and D Indoor Rowers and all SkiErgs Plastic cover for the bearing on the left side of the Model C or D Indoor Rower, opposite the flywheel, and the back side of all SkiErgs.

    1,21 €
Showing 1 - 25 of 34 items