- English
- Nederlands
No products
Prices are tax included
Product successfully added to your shopping cart
There are 0 items in your cart. There is 1 item in your cart.
General Information
Parts listed here are compatible with Model C Indoor Rowers. Model Cs were manufactured from 1993–2003.
Model C There are 26 products.
-
225,00 €
-
42,50 €
Nickel Chain with Connectors
For use with Model C, D and E Indoor Rowers. Includes on 8' 4" long chain with a brass swivel at the handle end and chain connector for the inside end. If your chain is badly rusted, has seized links or is broken, you will need to replace it with this part. See more info.
42,50 € -
25,00 €
Monitor Pickup and Screw Kit—Model A, C
For use with Model A and C Indoor Rowers. This is the pickup (sensor) and cable (wire) that transmit flywheel to the Performance Monitor on your indoor rower. If your monitor lights up with zeros but the display does not change when you begin rowing, you may need to replace this part. If the cable or cable housing is cut or broken you will definitely need...
25,00 € -
21,01 €
Indoor Rower Handle with Grips
Replacement handle for the Model D, E and Dynamic Indoor Rowers. Overmolded grips made of soft rubber won´t absorb sweat, grease or dirt. Does not include U-bolt nuts. See more info.
21,01 € -
19,51 €
Seat Top with Screws
For use on all Concept2 Indoor Rowers. Replacement seat top. 12" wide, 10" deep, 1½" thick, with contours for pelvic bones and tailbone. Mounting screws and lock washers (four each) included. Original equipment on Model C, D, E and Dynamic Indoor Rowers. Can be retrofitted on all Model B and most Model A Indoor Rowers, replacing the original "kidney"...
19,51 € -
17,50 €
-
16,00 €
-
13,50 €
Seat Roller, Top
For use with Model C, D, E and Dynamic Indoor Rowers. One of the 3-1/4 inch wide top seat rollers (two per machine; sold individually) that runs on the stainless steel track on the monorail. Mounting hardware that holds the roller on the seat frame is not included, because it can usually be re-used. If you need the hardware, order part number 1728...
13,50 € -
9,00 €
Damper Replacement Kit
For use with Model C Indoor Rowers. This is the lever and damper (shutter) on the side of the flywheel housing that slides up and down to change the airflow through the flywheel. Less air through the flywheel (setting = 1) means less drag when rowing; more air through the flywheel (setting = 10) means more drag. Fits Model C Indoor Rowers only. See more...
9,00 € -
8,49 €
Shock Cord
For use with Model C, D and E Indoor Rowers. This is the 12´ 6" long elastic shock cord (or bungee cord) that recoils the chain on recovery. If your chain recoils slowly—or not at all—between strokes, then you should inspect your existing shock cord. See more info.
8,49 € -
7,50 €
14 Tooth Quiet Sprocket—Model D and E
For use on the Model D and E Indoor Rower. This is the 14 tooth sprocket for the flywheel axle. If you need to replace the sprocket, you should replace the chain at the same time (see part number 1916). See more info.
7,50 € -
7,50 €
Flexfoot, Gray
For use with updated Model D, Model E and Dynamic Indoor Rowers. Also fits Model C and original Model D Indoor Rowers but is dark gray in color (for black, order part number 1017 instead). This flexfoot piece fits into the footstretcher covers (part numbers 1054 and 1055, sold separately) to make the complete footstretcher assembly. Footplate/Flexfoot...
7,50 € -
3,80 €
Seat Roller, Bottom
For use with Model C, D, E and Dynamic Indoor Rowers. This is one of the small bottom seat rollers (two per machine; sold individually) that runs under the top edge of the monorail. Does not include the mounting hardware (nut, bolt and spacers) that hold the roller on the seat frame, because it can usually be reused. If you need the hardware, order part...
3,80 € -
3,30 €
Footstrap
Size Long - ref 1517 - This footstrap will only work for indoor rowers made after July 21, 2006, RowErg and Dynamic (length: 76 cm) If your Indoor Rower (model C and D1) was made before July 21, 2006, order Size Sshort - ref 1501 instead. (length: 61 cm)
3,30 € -
3,10 €
Shock Cord Pulley
For use with Model C, D and E Indoor Rowers. This is a 3-3/8 inch diameter pulley that the shock cord (part number 1731) runs over inside the Concept2 Indoor Rower. There are four per machine. Sold individually. See more info.
3,10 € -
2,70 €
Monitor Mount Knob, 3/8-16
For use on all Model C, D, E, and Dynamic Indoor Rowers and the SkiErg. Using this knob instead of a nut makes it easier to take the monitor on and off of the equipment.
2,70 € -
2,70 €
17mm Bearing—Model C, D, E
For use on all Model C, D and E Indoor Rowers. This is the 17mm bearing located outside of the flywheel. The corresponding bearing cup (part number 1012) is sold separately. See more info.
2,70 € -
2,50 €
Caster Wheel
For use with Model C and original Model D Indoor Rowers. Replacement caster wheel located on the front foot of Model C and original Model D Indoor Rowers. Used when picking up the back end of the indoor rower and rolling it like a wheel barrow.
2,50 € -
2,20 €
Foot Cap
For use with Model A, B, C, D, E and Dynamic Indoor Rowers. This is the hard plastic cap that goes on the rear and/or front metal legs of the indoor rower to protect your carpet or floor and keep the machine from sliding back and forth while you row. Two to four per machine, depending on age and indoor rower model. Sold individually. See more info.
2,20 € -
1,50 €
Chain Idler Pulley
For use with Model C, D and E Indoor Rowers. These are the 1¼" diameter urethane pulleys that the chain runs over inside the indoor rower. There are two per machine: one is part of the traveling pulley (part number 1756); the other is mounted on a stationary axle and has two chain idler spacers (part number 1305) to keep it properly aligned. See more info.
1,50 € -
1,40 €
Slotted Chain Swivel Bushing—Model C, D, E
For use on all Model C, D and E Indoor Rowers. This swivel bushing is installed at the swivel/handle end of the chain to prolong chain life and provide smoother rowing. See more info.
1,40 € -
1,40 €
-
0,90 €
Bearing Cover
For use with Model C and D Indoor Rowers and all SkiErgs Plastic cover for the bearing on the left side of the Model C or D Indoor Rower, opposite the flywheel, and the back side of all SkiErgs.
0,90 € -
0,80 €
Handle Hook, Plastic—Model C, D, E
For use with Model C, D and E Indoor Rowers. This is the handle hook used on the Models C, D and E Indoor Rower. To store the handle long-term, place the handle up against the flywheel housing. For ease of use before or during a workout, placing the handle in the handle hook puts the handle within easy reach.
0,80 € -
0,62 €
S.C.A.M.—Model C, D, E
For use on the Model C, D and E Indoor Rower. SCAM stands for Shock Cord Adjustment Mechanism. This part holds each end of the shock cord. Order two per machine.
0,62 €
