For use with Model C, D and E Indoor Rowers. Includes on 8' 4" long chain with a brass swivel at the handle end and chain connector for the inside end. If your chain is badly rusted, has seized links or is broken, you will need to replace it with this part. See more info.
For use with Model D and E Indoor Rowers. This is the generator base and coil that transmit flywheel motion to and generates power for the Performance Monitor on your indoor rower. See more info.
For use on the Model D and E Indoor Rower. This is the 14 tooth sprocket for the flywheel axle. If you need to replace the sprocket, you should replace the chain at the same time (see part number 1916). See more info.
Replacement handle for the Model D, E and Dynamic Indoor Rowers. Overmolded grips made of soft rubber won´t absorb sweat, grease or dirt. Does not include U-bolt nuts. See more info.
For use on the Model D and E Indoor Rower.
For use with Model C, D, E and Dynamic Indoor Rowers. One of the 3-1/4 inch wide top seat rollers (two per machine; sold individually) that runs on the stainless steel track on the monorail. Mounting hardware that holds the roller on the seat frame is not included, because it can usually be re-used. If you need the hardware, order part number 1728...
For use on all Concept2 Indoor Rowers. Replacement seat top. 12" wide, 10" deep, 1½" thick, with contours for pelvic bones and tailbone. Mounting screws and lock washers (four each) included. Original equipment on Model C, D, E and Dynamic Indoor Rowers. Can be retrofitted on all Model B and most Model A Indoor Rowers, replacing the original "kidney"...
This special nut tool is required to replace the flywheel axle sprockets on Model C, D or E Indoor Rowers. Model D and E Axle and Sprocket Replacement
For use with Model C, D and E Indoor Rowers. This is the 12´ 6" long elastic shock cord (or bungee cord) that recoils the chain on recovery. If your chain recoils slowly—or not at all—between strokes, then you should inspect your existing shock cord. See more info.
For use with updated Model D, Model E and Dynamic Indoor Rowers. Also fits Model C and original Model D Indoor Rowers but is dark gray in color (for black, order part number 1017 instead). This flexfoot piece fits into the footstretcher covers (part numbers 1054 and 1055, sold separately) to make the complete footstretcher assembly. Footplate/Flexfoot...
This is the part of the indoor rower that connects to the Performance Monitor on one end and the chain guide brackets on the other. For use on all Model C and Model D Indoor Rowers. See more info.
For use with Model C, D, E and Dynamic Indoor Rowers. This is one of the small bottom seat rollers (two per machine; sold individually) that runs under the top edge of the monorail. Does not include the mounting hardware (nut, bolt and spacers) that hold the roller on the seat frame, because it can usually be reused. If you need the hardware, order part...
For use on the Model C, D and E Indoor Rower. This is the part that the chain passes through before entering into the flywheel assembly. See more info.
For use with Model C, original Model D and Retrofitted Model A and B Indoor Rowers. This is the 12" molded plastic part anchored with 4 screws and nuts to the metal footplates on the indoor rower, enabling you to adjust the Flexfoot (part number 1017, sold separately) to accommodate different foot sizes and body types. There are two per machine. See more...
T27 6-Lobe driver required to turn the front leg fasteners (part number 2952) on Model C, D (original and updated) and E Indoor Rowers.
For use with Model A, B, C and original D Indoor Rowers. Replacement nylon footstrap with buckle, approximately 24" long by 1" wide with a screwhole drilled approximately 7" from the buckle end. Two per machine. Sold individually.
For use with Model C, D and E Indoor Rowers. This is a 3-3/8 inch diameter pulley that the shock cord (part number 1731) runs over inside the Concept2 Indoor Rower. There are four per machine. Sold individually. See more info.
For use on all Model C, D and E Indoor Rowers. This is the 17mm bearing located outside of the flywheel. The corresponding bearing cup (part number 1012) is sold separately. See more info.
For use with Model C, D and E Indoor Rowers. These are the 1¼" diameter urethane pulleys that the chain runs over inside the indoor rower. There are two per machine: one is part of the traveling pulley (part number 1756); the other is mounted on a stationary axle and has two chain idler spacers (part number 1305) to keep it properly aligned. See more info.
For use on all Model C, D and E Indoor Rowers. This swivel bushing is installed at the swivel/handle end of the chain to prolong chain life and provide smoother rowing. See more info.
For use with Model A, B, C, D, E and Dynamic Indoor Rowers. This is the hard plastic cap that goes on the rear and/or front metal legs of the indoor rower to protect your carpet or floor and keep the machine from sliding back and forth while you row. Two to four per machine, depending on age and indoor rower model. Sold individually. See more info.
For use with Model C and D Indoor Rowers and all SkiErgs Plastic cover for the bearing on the left side of the Model C or D Indoor Rower, opposite the flywheel, and the back side of all SkiErgs.
For use with Model C and original Model D Indoor Rowers. Replacement caster wheel located on the front foot of Model C and original Model D Indoor Rowers. Used when picking up the back end of the indoor rower and rolling it like a wheel barrow.