skip to main content
/ //Model C
Model C

Parts listed here are compatible with Model C Indoor Rowers. Model Cs were manufactured from 1993–2003.

Model C Er zijn 25 producten

Toont 1 - 25 van de 25 items
  • 225,00 €

    225,00 €
    Meer
  • 42,50 €

    For use with Model C, D and E Indoor Rowers. Includes on 8' 4" long chain with a brass swivel at the handle end and chain connector for the inside end. If your chain is badly rusted, has seized links or is broken, you will need to replace it with this part. See more info.

    42,50 €
    In winkelwagen Meer
  • 25,00 €

    For use with Model C  Indoor Rowers. This is the pickup (sensor) and cable (wire) that transmit flywheel to the Performance Monitor on your indoor rower. If your monitor lights up with zeros but the display does not change when you begin rowing, you may need to replace this part. If the cable or cable housing is cut or broken you will definitely need to...

    25,00 €
    In winkelwagen Meer
  • 21,01 €

    Replacement handle for the Model D, E and Dynamic Indoor Rowers. Also retrofitable for Model A, B and C. Overmolded grips made of soft rubber won´t absorb sweat, grease or dirt. Does not include U-bolt nuts. See more info.

    21,01 €
    In winkelwagen Meer
  • 19,51 €

    For use on all Concept2 Indoor Rowers. Replacement seat top. 12" wide, 10" deep, 1½" thick, with contours for pelvic bones and tailbone. Mounting screws and lock washers (four each) included. Original equipment on Model C, D, E and Dynamic Indoor Rowers. Can be retrofitted on all Model B and most Model A Indoor Rowers, replacing the original "kidney"...

    19,51 €
    In winkelwagen Meer
  • 17,50 €

    Cog nut tool with clutch. Not compatible with the Model B Indoor Rower.

    17,50 €
    In winkelwagen Meer
  • 16,00 €

    For use on the Model D and E Indoor Rower, And retrofit for Model C when replacing the sprocket to Pn 1165

    16,00 €
    In winkelwagen Meer
  • 13,50 €

    For use with Model C, D, E and Dynamic Indoor Rowers. One of the 3-1/4 inch wide top seat rollers (two per machine; sold individually) that runs on the stainless steel track on the monorail. Mounting hardware that holds the roller on the seat frame is not included, because it can usually be re-used. If you need the hardware, order part number 1728...

    13,50 €
    In winkelwagen Meer
  • 9,00 €

    For use with Model C Indoor Rowers. This is the lever and damper (shutter) on the side of the flywheel housing that slides up and down to change the airflow through the flywheel. Less air through the flywheel (setting = 1) means less drag when rowing; more air through the flywheel (setting = 10) means more drag. Fits Model C Indoor Rowers only. See more...

    9,00 €
    In winkelwagen Meer
  • 8,49 €

    For use with Model C, D and E Indoor Rowers. This is the 12´ 6" long elastic shock cord (or bungee cord) that recoils the chain on recovery. If your chain recoils slowly—or not at all—between strokes, then you should inspect your existing shock cord. See more info.

    8,49 €
    In winkelwagen Meer
  • 7,50 €

    For use on the Model D and E Indoor Rower. This is the 14 tooth sprocket for the flywheel axle. If you need to replace the sprocket, you should  you should also order item 7071. PN 7071 is a tool to remove the gear from the flywheel axle. See more info.

    7,50 €
    In winkelwagen Meer
  • 7,50 €

    For use with updated Model D, Model E and Dynamic Indoor Rowers. Also fits Model C and original Model D Indoor Rowers but is dark gray in color (for black, order part number 1017 instead). This flexfoot piece fits into the footstretcher covers (part numbers 1054 and 1055, sold separately) to make the complete footstretcher assembly. Footplate/Flexfoot...

    7,50 €
    In winkelwagen Meer
  • 3,80 €

    For use with Model C, D, E and Dynamic Indoor Rowers. This is one of the small bottom seat rollers (two per machine; sold individually) that runs under the top edge of the monorail. Does not include the mounting hardware (nut, bolt and spacers) that hold the roller on the seat frame, because it can usually be reused. If you need the hardware, order part...

    3,80 €
    In winkelwagen Meer
  • 3,30 €

    For use with updated Model D, Model E and Dynamic Indoor Rowers.  Replacement nylon footstrap with buckle, approximately 30" long by 1" wide with a screwhole drilled approximately 9" from the buckle end. Two per machine. Sold individually. Model D/E Flexfoot Assembly Diagram

    3,30 €
    Meer
  • 3,10 €

    For use with Model C, D and E Indoor Rowers. This is a 3-3/8 inch diameter pulley that the shock cord (part number 1731) runs over inside the Concept2 Indoor Rower. There are four per machine. Sold individually. See more info.

    3,10 €
    In winkelwagen Meer
  • 2,70 €

    For use on all Model C, D, E, and Dynamic Indoor Rowers and the SkiErg. Using this knob instead of a nut makes it easier to take the monitor on and off of the equipment.

    2,70 €
    In winkelwagen Meer
  • 2,50 €

    For use with Model C and original Model D Indoor Rowers. Replacement caster wheel located on the front foot of Model C and original Model D Indoor Rowers. Used when picking up the back end of the indoor rower and rolling it like a whell barrow.

    2,50 €
    In winkelwagen Meer
  • 2,20 €

    For use with Model A, B, C, D, E and Dynamic Indoor Rowers. This is the hard plastic cap that goes on the rear and/or front metal legs of the indoor rower to protect your carpet or floor and keep the machine from sliding back and forth while you row. Two to four per machine, depending on age and indoor rower model. Sold individually. See more info.

    2,20 €
    In winkelwagen Meer
  • 1,50 €

    For use with Model C, D and E Indoor Rowers. These are the 1¼" diameter urethane pulleys that the chain runs over inside the indoor rower. There are two per machine: one is part of the traveling pulley (part number 1756); the other is mounted on a stationary axle and has two chain idler spacers (part number 1305) to keep it properly aligned. See more info.

    1,50 €
    In winkelwagen Meer
  • 1,40 €

    For use on all Model C, D and E Indoor Rowers. This swivel bushing is installed at the swivel/handle end of the chain to prolong chain life and provide smoother rowing. See more info.

    1,40 €
    In winkelwagen Meer
  • 1,40 €

    For use with the wooden handle on all models of indoor rowers. Connects the handle to the chain. The corresponding nuts are part number 240 for a Model A, B or C and part number 1235 for Model D and E.

    1,40 €
    In winkelwagen Meer
  • 0,90 €

    For use with Model C and D Indoor Rowers and all SkiErgs Plastic cover for the bearing on the left side of the Model C or D Indoor Rower, opposite the flywheel, and the back side of all SkiErgs.

    0,90 €
    In winkelwagen Meer
  • 0,80 €

    For use on the Model C, D and E Indoor Rower.

    0,80 €
    In winkelwagen Meer
  • 0,62 €

    For use on the Model C, D and E Indoor Rower. SCAM stands for Shock Cord Adjustment Mechanism. This part holds each end of the shock cord. Order two per machine.

    0,62 €
    In winkelwagen Meer
  • 0,22 €

    Used on the guide bracket of Model D Indoor Rowers, and on the rear leg of Model C and D Indoor Rowers.

    0,22 €
    In winkelwagen Meer
Toont 1 - 25 van de 25 items